TECAPEI GF30 glass filled Ultem

TECAPEI GF30 Nat Sabic Ultem2300 Series - Stock Shapes rods plates tubes Chemical Designation PEI Polyetherimide Main features high thermal and mechanical capacity high dielectric strength excellent strength and stiffness excellent tensile strength easy to machine inherent flame resistance Colour brown-beige Density 1.51 gcm3 Target Industries aircraft and aerospace technology electrical engineering automotive industry mechanical engineering Fillers 30 glass fibres Mechanical properties condition value Modulus of elasticity tensile test 73 F 800000 psi test method ASTM D 638 Tensile strength at break 73 F 18000 psi ASTM D 638 Elongation at break tensile test 73 F 3 ASTM D 638 Flexural strength 73 F 28000 psi ASTM D 638 Modulus of elasticity flexural test 73 F 800000 psi ASTM D 790 Compression strength 10 strain 26000 psi ASTM D 695 Compression strength 1 strain 3700 psi ASTM D 695 Compression strength 5 strain 18000 psi ASTM D 695 Compression modulus 73 F 390000 psi ASTM D 695 Impact strength Izod 73 F 1.1 ft-lbsin ASTM D 256 Rockwell hardness M Scale 110 Shear strength 73 F ASTM D732 14500 comment ASTM D 785 - psi Thermal properties condition value Deflection temperature 66 psi 14 414 F test method ASTM D 648 1 comment Deflection temperature 264 psi 14 409 F ASTM D 648 2 Service temperature short term 392 F - 3 Service temperature Long Term 356 F - 4 Thermal expansion CLTE 1.110 -5 ininF ASTM D 696 5 Thermal conductivity 1.56 BTU-inhr-ft2 -F ASTM D 2214 6 Electrical properties condition value volume resistance 116 3.010 16 cm ASTM D 257 1 Dielectric strength In Oil 630 Vmil ASTM D 149 2 Dielectric strength In Air 770 Vmil ASTM D 149 3 Dissipation factor 1kHz 50 RH 73F 0.0015 ASTM D 150 4 Dielectric constant 1kHz 50 RH 3.7 ASTM D 150 5 Other properties condition value Moisture absorption 24 hrs 73 F 0.16 ASTM D 570 1 Moisture absorption saturation 73 F 0.90 ASTM D 570 2 V0 - 3 pass FAR 25.853 4 Flammability UL94 Flammability 6 mm test method 1 injec

tion molded data 2 Injection molded data 3 Data obtained from public source 4 Data obtained from public source 5 Injection molded data 6 injection molded data comment test method 1 injection molded data 2 injection molded data 3 injection molded data 4 injection molded data 5 injection molded data comment 1 injection molded data 2 injection molded data 3 Injection molded data0.25mm thick 4 6 mm test specimen Resin specification ASTM D5205-10 PEI0110G30A96299 159 Mpa 224 Mpa 208oC Shapes specification ASTM D7293-06 S-PEI0213 This information reflects the current state of our knowledge and is intended only to assist and advise. It is given without obligation or liability. It does not assure or guarantee chemical resistance quality of products or their suitability in any legally binding way. Values are not minimum or maximum values but guidelines that can be used for comparative purposes in material selection. They are within the normal range of product properties and do not represent guaranteed property values. Testing under individual application circumstances is always recommended. Data is obtained from extruded shapes material unless otherwise noted. References to FDA compliance refer to the resins from which the products were made unless otherwise noted. All trade and patent rights should be observed. All rights reserved. Data sheet values are subject to periodic review the most recent update can be found at www.ensingerplastics.com. Ensinger Inc. Headquarters 365 Meadowlands Boulevard Washington PA 15301 USA Phone 800-243-3221 Sales Phone 800-869-4029 Technical Fax 724-746-9209 salesensingerusa.com Date 20150728 Version A0