TECAFLON PVDF natural

TECAFLON PVDF natural - Stock Shapes rods plates tubes Chemical Designation PVDF Polyvinylidene fluoride Main features excellent chemical resistance inherent flame resistance high gamma radiation resistance good UV and weather resistance good mechanical properties low moisture absorption good machinability Colour white Density 1.78 gcm3 Target Industries chemical plant engineering process engineering medical technology cleanroom technology food processing food engineering Mechanical properties condition value Modulus of elasticity tensile test 73 F 350000 psi ASTM D 638 Tensile strength at yield 73 F 8100 psi ASTM D 638 Tensile strength at break 73 F 7800 psi ASTM D 638 Elongation at break tensile test 73 F 35 ASTM D 638 Flexural strength 73 F 9700 psi ASTM D 790 Modulus of elasticity flexural test 73 F 320000 psi ASTM D 790 Compression strength 73 F 10 strain 11600 psi ASTM D 695 Compression 73 F 1 strain 3200 psi ASTM D 695 Compression modulus 73 F 160000 psi ASTM D 695 Impact strength Izod 73 F 2.49 ft-lbsin ASTM D 256 Rockwell hardness 73 F M scale 79 Thermal properties condition test method ASTM D 785 value Melting temperature comment test method 346 F ASTM D 3418 comment Deflection temperature 264 psi 235 F ASTM D 648 1 Deflection temperature 66 psi 300 F ASTM D 648 2 Service temperature short term 300 F - 3 Service temperature Long Term 300 F - 4 Thermal expansion CLTE 7.110 -5 ininF ASTM D 696 5 Thermal conductivity 1.32 BTU-inhr-ft2 -F ASTM C 177 6 Electrical properties condition value volume resistance 73 F 510 14 cm ASTM D 257 1 510 Vmil ASTM D 149 2 Dielectric strength test method comment Dissipation factor 60 Hz 73 F 0.06 ASTM D 150 3 Dielectric constant 60 Hz 73 F 50 RH 9 ASTM D 150 4 Other properties condition value Moisture absorption 24 hrs 73 F 0.02 Flammability UL94 test method V0 1 publicly sourced data 2 Injection molded samples 3 publicly sourced data 4 publicly sourced data comment ASTM D 570 - 1 publicly sourced data 2 Injec

tion molded samples 3 Data obtained from public source 4 Data obtained from public source 5 publicly sourced data 6 publicly sourced data 1 1 Thickness greater than 0.1 mm Injection molded samples Resin specification ASTM D3222-05 Reapproved 2015 Type II Shapes specification ASTM D 6713-14 S-PVDF0111 This information reflects the current state of our knowledge and is intended only to assist and advise. It is given without obligation or liability. It does not assure or guarantee chemical resistance quality of products or their suitability in any legally binding way. Values are not minimum or maximum values but guidelines that can be used for comparative purposes in material selection. They are within the normal range of product properties and do not represent guaranteed property values. Testing under individual application circumstances is always recommended. Data is obtained from extruded shapes material unless otherwise noted. References to FDA compliance refer to the resins from which the products were made unless otherwise noted. All trade and patent rights should be observed. All rights reserved. Data sheet values are subject to periodic review the most recent update can be found at www.ensingerplastics.com. Ensinger Inc. Headquarters 365 Meadowlands Boulevard Washington PA 15301 USA Phone 800-243-3221 Sales Phone 800-869-4029 Technical Fax 724-746-9209 salesensingerusa.com Date 20230621 Version A1