Kyron GC-100 For the Bur n In and Test Socket Market Kyron GC-100 is a non fiber filled injection molded polymer designed specifically for burn in test socket applications that require an extremely high degree of stability yet also requires superior micro machinable. 12 Kyron GC-100 vs. Other High End Materials Polymeric Stability Flexural modulus of over 1000000 psi Available in 10 x 10 plates of 6mm 9mm or 12mm thick Tensile elongation of 3.0 for precise hole placement Extremely stable during usage CTE of 1.85x10-5th Properties Method Kyron GC-100 Semitron MDS-100 Vespel SCP-5000 Vespel SP1 Semitron MP-370 Kyron EPM-2204 Flexural Modulus psi D790 1100000 1400000 836000 450000 625000 750000 Tensile Elongation D638 3.0 1.5 7.5 7.5 3 21 CTE inin F x 10 XY axis E831 1.85 1.1 2.6 3.05 2.5 2.0 HDT 264 psi F D648 445 410 632 600 410 410 Water Absorption D570 0.09 0.1 0.1 0.24 0.1 0.37 Relative Cost Kyron GC-100 Product Positioning 8 12 Semitron MDS 100 4 A formula which combines CLTE stiffness K ey Benef it s Kyron GC-100 0 Ketron 1000 PEEK 4 Kyron GC-100 provides engineers with a more stable material than Vespel SCP-5000 at a reduced cost. mcam.com Superior Performance Duratron T4203 PAI Semitron MP 370 Duratron U1000 PEI Kyron EPM-2204 Duratron T5030 PAI 2.5 Ketron Semitron MP 370 Duratron T4203 PAI PoIyimide 5.0 Duratron 1000 PEEK U1000 PEI Machinability Rating A formula which combines heat resistance ductility PoIyimide fill 0 Kyron GC-100 Kyron EPM-2204 8 Duratron T5030 PAI Polymeric Stability A formula which combines CLTE stiffness Semitron MDS 100 2.5 5.0 Machinability Rating A formula which combines heat resistance ductility fill Socket Type Basic Challenging Demanding Hole Size 0.6 - 0.4 Socket Type Basic 0.4 - 0.3 Challenging 0.6 - 0.4 Pitch SizeHole Size 1.0 - 0.35 0.4 -- 0.3 0.35 0.25 0.30.25 - 0.1 - 0.18 Pitch Size 1.0 - 0.35 0.35 - 0.25 0.25 - 0.18 0.2 0.2 - 0.1 0.05 - 0.01 Wall Wall 0.2 I0 CountI0 Count 1000 1000 0.2 - 0.1 2500 2500 0.
3 - 0.1 Demanding 0.05 - 0.01 2500 2500 MCAMconnect contactmcam.com Tes t Socke t M a t e r ia l COMPARISON Versus GF-PAI Kyron GC-100 provides the stiffness Versus MDS-100 Designed to complement MDS-100 of GF PAI with improved small hole machinability lower moisture absorption offers relatively similar properties but available in thicker cross sections Versus Standard Polyimides Kyron GC-100 offers 2X higher stiffness 2.5X less moisture absorption 35 lower CTE and 2X better hole accuracy Kyron GC-100 Data Sheet Units Test Method Typical Average Value Specific Gravity 73F - ASTM D792 1.52 Tensile Strength at break 73F psi ASTM D638 16000 Tensile Modulus of Elasticity 73F psi ASTM D638 1100000 Tensile Elongation at break 73F ASTM D638 3 Shear Strength 73F psi ASTM D732 11000 Flexural Strength 73F psi ASTM D790 24000 Flexural Modulus of Elasticity 73F psi ASTM D790 1100000 Compressive Strength 10 Deformation 73F psi ASTM D695 23000 Compressive Modulus of Elasticity 73F psi ASTM D695 600000 Hardness Rockwell 73F - ASTM D785 M100R123 Notched Izod notched 73F ft. lb.in.2 ASTM D256 Type A 0.7 Coefficient of Linear Thermal Expansion in.in.F ASTM E-831 TMA 1.85 x 10-5 Heat Deflection Temperature 264 psi F ASTM D648 445 Melting Point crystalline peak F ASTM D3418 644 - 480 Continuous Service Temp in Air Max. F 1 Thermal Conductivity BTU-in.hr-ft. -F ASTM F433 2.36 Surface Resistivity ohmssquare EOSESD S11.11 1013 Flammability UL-94 1.5mm 116 in.23 - UL-94 V-0 Water Absorption Immersion Saturation2 by wt. ASTM D570 0.44 Other Electrical Properties Thermal Properties Mechanical Properties Property 2 1 D ata represents Mitsubishi Chemical Advanced Materials estimated maximum long-term service temperature based on practical field experience. 2 Specimens 18 thick x 2 diameter or square. 3 E stimated rating based on available data. The UL-94 Test is a laboratory test and does not relate to actual fire hazard. Contact Mitsubishi Chemical Advandced Materia
ls for specific UL Yellow Card recognition number. Distributed by All statements technical information and recommendations contained in this publication are presented in good faith and are as a rule based upon tests and such tests are believed to be reliable and practical field experience. The reader however is cautioned that Mitsubishi Chemical Advanced Materials does not guarantee the accuracy or completeness of this information and it is the customers responsibility to determine the suitability of Mitsubishi Chemical Advanced Materials products in any given application. Ketron and Kyron are registered trademarks of the Mitsubishi Chemical Advanced Materials group of companies. Vespel is a registered trademark of E.I. DuPont. Design and content created by Mitsubishi Chemical Advanced Materials and are protected by copyright law. Copyright Mitsubishi Chemical Advanced Materials. All rights reserved. MCM NA 006 6.11.19
