TECAPEEK ELS nano black

TECAPEEK ELS nano black - Stock Shapes rods plates tubes Chemical Designation PEEK Polyetheretherketone Main features high dimensional stability high continuous use temperature high strength very good chemical resistance electrically conductive high thermal and mechanical capacity good machinability high toughness Colour black opaque Density 1.36 gcm3 Fillers CNT Target Industries aircraft and aerospace technology electronics mechanical engineering semiconductor technology computer technology Mechanical properties condition value Tensile strength 2 inmin 15400 psi DIN EN ISO 527-2 Modulus of elasticity tensile test 0.039 inmin 696000 psi DIN EN ISO 527-2 Tensile strength at yield 2 inmin 15400 psi DIN EN ISO 527-2 Elongation at yield tensile test 2 inmin 4 DIN EN ISO 527-2 Elongation at break tensile test 2 inmin 4 DIN EN ISO 527-2 Flexural strength 0.078 inmin 2.25 lbf 25800 psi DIN EN ISO 178 Modulus of elasticity flexural test 0.078 inmin 2.25 lbf 682000 psi DIN EN ISO 178 Compression strength 5 strain 0.197 inmin 2.25 lbf 15400 psi EN ISO 604 3 Compression strength 2 strain 0.197 inmin 2.25 lbf 6820 psi EN ISO 604 4 Compression strength 1 strain 0.197 inmin 2.25 lbf 3920 psi EN ISO 604 5 Compression modulus 0.197 inmin 2.25 lbf 522000 MPa EN ISO 604 6 Impact strength Charpy ft-lbsin2 27.6 DIN EN ISO 179-1eU 7 ISO 2039-1 8 Ball indentation hardness Thermal properties test method 36700 condition psi value comment 1 2 test method Glass transition temperature 297 F DIN EN ISO 11357 Melting temperature 646 F DIN EN ISO 11357 Service temperature short term 572 F - Service temperature long term 500 F - Thermal expansion CLTE 73 - 140F long. 2.78 10-5 ininF DIN EN ISO 11359-12 Thermal expansion CLTE 73 - 212F long. 2.78 10-5 ininF DIN EN ISO 11359-12 Thermal expansion CLTE 212 - 300F long. 3.89 10-5 ininF DIN EN ISO 11359-12 Specific heat 0.00026 BTUlb-F ISO 22007-42008 Thermal conductivity 3.19 BTU-inhr-ft2 -F ISO 22007-42008 comment 1 2 Electrical properties conditi

on value surface resistivity Conductive rubber 73F 12 r.h. 102 - 104 DIN EN 61340-2-3 volume resistivity Conductive rubber 73F 12 r.h. 103 - 105 cm DIN EN 61340-2-3 Other properties condition value Water absorption 24h 96h 73F 0.02 0.03 test method 1 - 2 Resistance to weathering - 3 V0 DIN IEC 60695-11-10 4 corresponding to 1 Specimen in 0.787 thickness comment DIN EN ISO 62 Resistance to hot water bases Flammability UL94 1 Found in public sources. 2 Found in public sources. Individual testing regarding application conditions is mandatory. comment 1 test method 1 For tensile test specimen type 1b 2 For flexural test support span 2.52 norm specimen. 3 Specimen 0.39 0.39 x 0.39 4 Specimen 0.39 x 0.39 x 0.39 5 Specimen 0.39 x 0.39 x0.39 6 Specimen 0.39 x 0.39 x 1.97 modulus range between 0.5 and 1 compression. 7 For Charpy test support span 2.52 norm specimen. 8 Specimen in 0.157 thickness 1 ca. 1.57 h0.512 2 good resistance 3 limited resistance 4 Corresponding means no listing at UL yellow card. The information might be taken from resin stock shape or estimation. Individual testing regarding application conditions is mandatory. TECAPEEK products are based on Victrex PEEK polymer. This information reflects the current state of our knowledge and is intended only to assist and advise. It is given without obligation or liability. It does not assure or guarantee chemical resistance quality of products or their suitability in any legally binding way. Values are not minimum or maximum values but guidelines that can be used for comparative purposes in material selection. They are within the normal range of product properties and do not represent guaranteed property values. Testing under individual application circumstances is always recommended. Data is obtained from extruded shapes material unless otherwise noted. References to FDA compliance refer to the resins from which the products were made unless otherwise noted. All trade and patent rights should be observed.

All rights reserved. Data sheet values are subject to periodic review the most recent update can be found at www.ensingerplastics.com. Ensinger Inc. Headquarters 365 Meadowlands Boulevard Washington PA 15301 USA Phone 800-243-3221 Sales Phone 800-869-4029 Technical Fax 724-746-9209 salesensingerusa.com Date 20210909 Version A0