TECANAT natural
TECANAT natural - Stock Shapes rods plates tubes Chemical Designation PC Polycarbonate Main features excellent impact strength excellent strength and stiffness excellent dimensional stability good machinability Colour transparent transparent Density 1.19 gcm3 Target Industries aircraft and aerospace technology food engineering food processing cleanroom technology packaging and paper machinery Mechanical properties condition value test method comment Modulus of elasticity tensile test 73 F 340000 psi ASTM D 638 Tensile strength at yield 73 F 9300 psi ASTM D 638 1 Injection molded data 2 Injection molded data 3 Injection molded data 4 per ASTM D732 Elongation at break tensile test 73 F 90 ASTM D 638 Flexural strength 73 F 12000 psi ASTM D 790 Modulus of elasticity flexural test 73 F 340000 psi ASTM D 790 Compression strength 1 strain 73 F 2100 psi ASTM D 695 Compression strength 10 strain 73 F 10000 psi ASTM D 695 Compression modulus 73 F 245000 psi ASTM D 695 Impact strength Izod 73 F 2.5 ft-lbsin ASTM D 256 Rockwell hardness 73 F M Scale R Scale 70 118 ASTM D 785 Shore hardness D scale 79 ASTM D 785 Coefficient of friction Dynamic 40 psi 50 fpm 0.38 ASTM D 3702 2 Wear K factor Against Steel 40 psi 50 fpm 250010 - in-minft-lbs-hr ASTM D 3702 3 9900 psi - 4 condition value Shear strength Thermal properties Vicat softening point 10 1 test method comment 309 F ASTM D 1525 1 Deflection temperature 66 psi 280 F ASTM D 648 2 Deflection temperature 264 psi 270 F ASTM D 648 3 Service temperature Intermittent 275 F - Service temperature Long Term 250 F - 4 Thermal expansion CLTE 3.8 10-5 ininF ASTM D 696 5 Specific heat 0.30 BTUlb-F - 6 Thermal conductivity 1.39 BTU-inhr-ft2 -F ASTM C 177 7 Electrical properties condition value test method comment volume resistance 1.010 17 cm ASTM D 257 1 Dielectric strength 378 Vmil ASTM D 149 2 Dissipation factor 60 Hz 73 F 0.0009 ASTM D 150 3 Dielectric constant 60 Hz 73 F 50 RH 3.17 ASTM D 150 4 Dielectric constant 1MHz 2.96
ASTM D 150 5 Other properties condition value test method Moisture absorption 24 hrs 73 F 0.13 ASTM D 570 1 Moisture absorption saturation 73 F 0.35 ASTM D 570 2 - 3 Flammability UL94 HB 1 Injection molded data 2 Injection molded data 3 Injection molded data 4 per UL746B 5 Injection molded data 6 per ASTM C351 Injection molded data 7 Injection molded data 1 Injection molded data 2 Injection molded data 3 Injection molded data 4 Injection molded data 5 Injection molded data comment 1 Injection molded data 2 Injection molded data 3 1.47mm thickness Injection molded data Resin specification ASTM D3935-09 PC0150B34840 Shapes specification ASTM D6098-10 S-PC0111 This information reflects the current state of our knowledge and is intended only to assist and advise. It is given without obligation or liability. It does not assure or guarantee chemical resistance quality of products or their suitability in any legally binding way. Values are not minimum or maximum values but guidelines that can be used for comparative purposes in material selection. They are within the normal range of product properties and do not represent guaranteed property values. Testing under individual application circumstances is always recommended. Data is obtained from extruded shapes material unless otherwise noted. References to FDA compliance refer to the resins from which the products were made unless otherwise noted. All trade and patent rights should be observed. All rights reserved. Data sheet values are subject to periodic review the most recent update can be found at www.ensingerplastics.com. Ensinger Inc. Headquarters 365 Meadowlands Boulevard Washington PA 15301 USA Phone 800-243-3221 Sales Phone 800-869-4029 Technical Fax 724-746-9209 salesensingerusa.com Date 20230525 Version A1