Technical Data Sheet KYDEX 7200ST Smoke and toxicity compliant aviation sheet Introduction KYDEX 7200ST is a high performance thermoplastic sheet designed for use in aviation interior applications where smoke and ABD0031 or BSS7239 toxicity compliance is required. General Information KYDEX 7200ST meets the flammability and smoke development requirements set forth in Federal Aviation Regulations FAR 25.853 paragraphs a and d Part V as well as the toxicity requirements for Airbus ABD0031 and Boeing BSS7239. Its wide processing window and ease of thermoforming makes it ideal for complex parts. Suggested Applications Armrests Tray tables Kick panels Trim parts Features Meets flammability and smoke development requirements listed in FAR 25.853a and d Part V Compliant to ABD0031 and BSS7239 toxicity specifications Excellent formability and fabrication characteristics Allows for tight tolerance control Available in P3 Velour Matte in thicknesses from 1.19mm to 4.75mm 0.047 to 0.187 Environmental and Safety Considerations SEKISUI SPI is committed to ensuring that its products can be manufactured transported stored used disposed and recycled with an appropriate regard for safety health and environmental protection. We support the safe handling of our products. Please contact our Technical Service department at 800.682.8758 for resources or visit our website httpwww.sekisui-spi.com. For Material Safety Data Sheets please call 800.325.3133. SEKISUI SPI ISO 9001 and 14001 Certified Customer Service 6685 Low St Bloomsburg PA 17815 USA Phone 800.325.3133 1.570.389.5810 Outside the US 1.570.389.5814 Fax 800.452.0155 1.570.387.7786 Email infosekisui-spi.com Technical Service Phone 800.682.8758 Fax 1.570.387.8722 Outside the US 1.570.387.6997 techservicesekisui-spi.com sekisui-spi.com 2015 SEKISUI Polymer Innovations LLC. All Rights Reserved. KYDEX ALLEN designLab and FSTLab are trademarks of SEKISUI Polymer Innovations LLC. 032615 Technical Data Sheet KYDEX 7200ST Smok
e and toxicity compliant aviation sheet Physical Properties Test Method Typical Value1 Specific Gravity ASTM D-792 1.25 Water Absorption 24hr ASTM D-570 0.16 Rockwell Hardness R-Scale ASTM D-785 112 Property PHYSICAL MECHANICAL Tensile Strength ASTM D-638 53.5 MPa 7760 psi Tensile Modulus ASTM D-638 2868 MPa 416000 psi Flexural Strength ASTM D-790 87.6 MPa 12700 psi Flexural Modulus ASTM D-790 2758 MPa 400000 psi Compressive Strength yield ASTM D-695 73.1 MPa 10600 psi Compressive Modulus ASTM D-695 2718 MPa 394000 psi Shear Strength ASTM D-732 45.5 MPa 6600 psi Bearing Strength 4 deflection ASTM D-953 27.6 MPa 4000 psi Bearing Strength max. ASTM D-953 246 MPa 35700 psi Gardner Drop Dart Impact GE ASTM D-5420 46.9 J 415 in-lbf Heat Deflection Temperature HDT 264psi 1.8 MPa unannealedannealed ASTM D-648 100oC 212oF Coefficient of Thermal Expansion ASTM E-831 51.4 mmoC 28.6ininoF ASTM D-149 23.8 kVmm 605 Vmil THERMAL ELECTRICAL Dielectric Strength oil FLAMABILITY 2 Vertical Burn 60-second FAR 25.853ai PASS Vertical Burn 12-second FAR 25.853aii PASS NBS Smoke Density FAR 25.853d Part V Dmax 200 Airbus Toxic Gas Generation ABD-0031 PASS Boeing Toxic Gas Generation BSS 7239 PASS 1 Values based upon 0.125 3.17mm sheet unless otherwise specified 2 All Thicknesses Not intended for specification purposes. SEKISUI SPI ISO 9001 and 14001 Certified Customer Service 6685 Low St Bloomsburg PA 17815 USA Phone 800.325.3133 1.570.389.5810 Outside the US 1.570.389.5814 Fax 800.452.0155 1.570.387.7786 Email infosekisui-spi.com Technical Service Phone 800.682.8758 Fax 1.570.387.8722 Outside the US 1.570.387.6997 techservicesekisui-spi.com Because we cannot anticipate or control the many different conditions under which this information and our products may be used we do not guarantee the applicability of the accuracy of this information or the suitability of our products in any given situation. Users should conduct their own tests to determine the suitability of each product for their
particular purposes. Data in the physical property table represents typical values and are to serve only as a guide for engineering design. Results are obtained from specimens under ideal laboratory conditions. Right to change physical properties as a result of technical progress is reserved. THE PRODUCTS DISCUSSED ARE SOLD WITHOUT WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE EITHER EXPRESSED OR IMPLIED EXCEPT AS PROVIDED IN OUR STANDARD TERMS AND CONDITIONS OF SALE. Buyer assumes all responsibility for loss or damage arising from the handling and use of our products whether done in accordance with directions or not. In no event shall the supplier or the manufacturer be liable for incidental or consequential damages. Also statements concerning the possible use of our products are not intended as recommendations to use our products in the infringement of any patent. Consult local code and regulatory agencies for specific requirements regarding code compliance transporting processing recycling and disposal of our product. Product not intended for use as a heat resistant surface. Texture product grade and other conditions may cause variations in appearance. sekisui-spi.com This information supersedes all previously published data. 2015 SEKISUI Polymer Innovations LLC. All Rights Reserved. KYDEX ALLEN designLab and FSTLab are trademarks of SEKISUI Polymer Innovations LLC. 032615
