PALGARD Notes The table depicting the typical properties of PALGARD sheets appears below. Note that some of the displayed properties are typical to polycarbonate the material PALGARD is made of while others relate to a typical 3 mm 18 in. thick PALGARD sheet. Material Scratch Resistant Polycarbonate Sheet Conditions units and values in U.S. Customary units are presented in the table within parentheses. All the results depicted in this table were obtained by following the indicated ASTM method except where another method is indicated by the appearance of this symbol b. Updated 6.13.2016 SY Property Conditions U.S. Customary ASTM Method Units - SI U.S. Customary Value U.S. Customary Physical D-1505 gcm3 lbft3 1.2 75 24 hr. 23C D-570 0.15 Tensile strength at yield 10 mmmin 0.4 in.min D-638 MPa psi 62 9000 Tensile strength at break 10 mmmin 0.4 in.min D-638 MPa psi 65 9500 Elongation at yield 10 mmmin 0.4 in.min D-638 6 Elongation at break 10 mmmin 0.4 in.min D-638 110 Density Water Absorption Mechanical Tensile Modulus of Elasticity 10 mmmin 0.4 in. min D-638 MPa psi 2378 345000 Flexural Modulus 1.3 mmmin 0.05 in.min D-790 MPa psi 2378 345000 Flexural Strength at Yield 1.3 mmmin 0.05 in.min D-790 MPa psi 93 13500 Notch Impact Strength Izod 23C 73F D-256 Jm ftlbfin. 800 15 Notch Impact Strength Charpy 23C 73F D-256 Jm ftlbfin 800 15 3 mm 0.12 in. Sheet ISO-66031b J ftlbf 158 117 D-785 R scale M scale 125 70 Impact Falling Weight Rockwell Hardness Abrasion Taber Process 100 Cycles CS-10F Wheel 500g D-1044 Haze 4.0 Compressive Strength 1.3 mmmin .05 in.min D-695 MPa psi 86 12500 Compressive Modulus 1.3 mmmin .05 in.min D-695 MPa psi 2378 345000 Shear strength at Yield 1.3 mmmin .05 in.min D-732 MPa psi 41 6000 Shear strength at Break 1.3 mmmin .05 in.min D-732 MPa psi 68 10000 Shear Modulus 1.3 mmmin .05 in.min D-732 MPa psi 786 114000 Long Term Service Temperature C F -75 to 100 -175 to 212 Short Term Service Temperature C F -75 to 120 -175 to 250 Thermal Heat Def
lection Temperature Load 1.82 Mpa 264 psi D-648 C F 132 270 Vicat Softening Temperature Load 1 kg 2.2 lb D-1525 C F 150 300 Coefficient of Linear Thermal Expansion Thermal Conductivity D-696 10-5C 10-5F 6.5 3.6 C-177 WmK Btu-in.hr-ft2-F 0.21 1.46 Specific Heat Capacity C-351 kJkgK BtulbF 1.26 0.31 D-1003 0.5 D-1003 Optical Haze Light Transmission 3 mm 0.12 in. Clear Sheet 3 mm 0.12 in. Clear Sheet 89 Refractive Index Clear Sheet D-542 1.59 Yellowness Index 3 mm 0.12 in. Clear Sheet D-1925 1 Electrical Dielectric Constant 50 Hz D-150 3 1 MHz D-150 2.9 0.9 50 Hz D-150 1 MHz D-150 Dielectric Strength Short Time 500 Vs D-149 kVmm Vmil 30 770 Surface Resistance Ketley D-257 Ohm 5.1x1015 Volume Resistance Ketley D-257 Ohm-cm 1.3x1017 Dissipation Factor 11