SCS1000 Contractors silicone sealant Product Description Typical Performance Properties SCS1000 Contractors silicone sealant is a one-component acetoxy silicone material that provides excellent weatherability and elasticity for general purpose sealing and bonding. SCS1000 silicone sealant is a paste material which cures into a flexible rubber when exposed to atmospheric moisture. Performance Silicone Durability - Cured silicone provides excellent longterm resistance to natural weathering humidity and high low temperatures with negligible change in elasticity. 25 Movement Capacity - Can accommodate 25 movement in both extension and compression and has excellent recovery after cycling. Thermal Stability - Once properly cured the material remains fully elastic over a range of -45F -48C to 350F 204C. Low VOC - significantly lower than the U.S. Green Building Councils Leadership in Energy and Environmental Design L.E.E.D. programs requirements. Application Fast Cure Time - Tack free in 30 minutes and full cure of many common bead sizes in 24-48 hours. Durable Adhesion - Able to bond to many common substrates and finishes including glass ceramic tiles porcelain painted surfaces some plastics cultured marble polished granites and marbles and many composite materials including fiberglass. Gunnability - The uncured silicone can be easily gunned and tooled under hot or cold conditions. Workability - Non-sag paste makes application possible on horizontal vertical or overhead surfaces. GE is a registered trademark of General Electric Company and is under license by Momentive Performance Materials Inc. Momentive Performance Materials provides versatile materials as the starting point for its creative approach to ideas that help enable new developments across hundreds of industrial and consumer applications. We are helping customers solve product process and performance problems our silanes fluids elastomers sealants resins adhesives urethane additives and other specialt
y products are delivering innovation in everything from car engines to biomedical devices. From helping to develop safer tires and keeping electronics cooler to improving the feel of lipstick and ensuring the reliability of adhesives our technologies and enabling solutions are at the frontline of innovation. Licensed Products SCS1000 Contractors silicone sealant Basic Uses Colors SCS1000 sealant is a candidate for use Contractors SCS1000 sealant series is available in 4 standard colors and translucent In general purpose sealing glazing applications. As a formed-in-place rubber gasket seal on a variety of materials and for sealing of sheet metal skylights HVAC componentry glass block metalplastic signs marine hardware. For bedding and grouting of bathroom and kitchen tiles. As a seal around bathroom fixtures and countertops air dryers and drains. For increased mold and mildew resistance consider SCS1700 Sanitary. Grade Color SCS1001 ...........................Translucent SCS1002 ...........................White SCS1003 ...........................Black SCS1009 ...........................Aluminum metallic SCS1097 ...........................Bronze Limitations Customer Evaluation Customers must evaluate Momentive Performance Materials MPM products and make their own determination as to fitness of use in their particular applications. Packaging Contractors SCS1000 sealant is available in 10.1 fl. oz. 299 ml cartridges with either removable or fixed nozzles. Cases contain 24 cartridges. P. 02 SCS1000 sealant is not recommended For use underwater or in when in continuous contact with water. When paintability is desired or necessary. Consider SCS7000 Paintable. In Structural Silicone Glazing SSG Applications. On mirrors. On wet damp frozen or contaminated surfaces. On masonry sawn stone surfaces lead copper or brass. SCS1000 Contractors silicone sealant Technical Services Additional technical information literature laboratory testing and application engineering
may be available upon request from MPM. Any technical advice furnished by MPM or any representative of MPM concerning any use or application of any MPM product is believed to be reliable but MPM makes no warranty expressed or implied of suitability for use in any application for which such advice is furnished. Applicable Standards SCS1000 sealant meets the requirements of the following specifications ASTM C920 U.S. Federal TT-S-001543A TT-S-00230C. USDA MPM has on file documentation from USDA which states that SCS1001 SCS1002 SCS1003 and SCS1009 sealants are chemically acceptable for use on surfaces in official establishments operating under the Federal Meat and Poultry Inspection Program. SCS1097 Bronze doesnot meet USDA acceptance criteria. For further information contact MPM Product Regulatory Compliance. The final granting of authorization for the proposed use of such compounds is the responsibility of the inspector in chargeof the official plant. Technical assistance will be provided by the Product Safety Branch of USDA upon request. FDA The following SCS1000 sealantscolors are compositionally in compliance with 21 CFR 177.2600 Rubber articles intended for repeated use 21 CFR 175.105 Adhesives and 21 CFR 175.300 Resinous and Polymeric Coatings SCS1001 SCS1002 SCS1003 SCS1009 and SCS1097. The use of these adhesive sealants is subject to the following conditions The adhesive sealant is applied in accordance with Good Manufacturing Practice at a thickness not to exceed 6mm 14 inch from an exposed edge. As a continuous film between joints acting as a functional barrier between the food and the substrate area underneath the joint. The adhesive sealant must be cured for a minimum of 14 days at or above 23C 73F and 50 Relative Humidity. The operating temperature of the adhesive sealant after cure must not exceed 177C 350F. The above sealants mentioned should be evaluated to determine bond strength for each specific substrate and application. If enhanced adhesion i
s desired the evaluation of a primer is recommended. Only SS4179 primer may be used in repeated contact with food under 21 CFR 175.300. Resinous and Polymeric Coatings may be used. NSF SCS1001 SCS1002 SCS1003 and SCS1009 sealants are listed under NSFANSI STANDARD 51 Food Equipment Materials. P. 03 SCS1000 Contractors silicone sealant Specifications Typical property values of SCS1000 silicone sealant as supplied and cured are set forth in the table below. Typical product data values should not be used as specifications. Typical Properties Supplied Property Value1 Test Method Consistency Paste NA Polymer 100 silicone NA VOC 20 g l WPSTM C1454 Work Life tooling time 5-10 minutes NA Tack Free Time 73F 23C 50 RH 15-30 minutes ASTM C679 Typical Properties Cured after cure of 21 days at 73F 23C 50 Relative Humidity Property Value1 Test Method Ultimate Tensile Strength 300 psi 2.1 MPa ASTM D412 Ultimate Elongation 433 ASTM D412 Cure Time 14 or 6 mm deep section 73F 23C 50 RH 24 hours NA Hardness Durometer Type A Indentor 27 ASTM D2240 Service Temperature Range after cure -55F to 350F -48C to 177C NA 1 Average value. Actual value may vary. P. 04 SCS1000 Contractors silicone sealant Installation In all cases it is important to confirm the acceptability of each sealant-substrate combination with an adhesion test prior to proceeding with use. Some materials with variable surface characteristics may require the use of a primer to help obtain durable long-term adhesion. See Construction Primers datasheet. Surface Preparation Surfaces must be clean dry and sound prior to application of the sealant. All contaminants impurities or other adhesion inhibitors such as moisturefrost oils old sealants soaps and other surface treatments etc. must be removed from the surfaces to which the sealant is intended to adhere. For cleaning a solvent-dampened clean rag usually produces the desired result. Isopropyl Alcohol IPA is a commonly-used solvent and has proven useful for most substr
ates. When handling solvents refer to manufacturers MSDS for information on handling safety and personal protective equipment. Masking The use of masking tape is recommended where appropriate to ensure a neat job and to protect adjoining surfaces from over-application of sealant. Masking tape should be removed immediately after tooling the sealant and before the sealant begins to skin over tooling time. P. 05 Sealant Application Apply sealant in a continuous operation applying a positive pressure adequate to properly fill and seal the seam cavity or joint. Tool or strike the sealant with an appropriate tool applying light pressure to spread the material against the joint surfaces for a neat application. Sealant application is not recommended when the temperature is below 40F 4C or if frost or moisture is present on the surfaces to be sealed. Application of SCS1000 sealant is not recommended to surfaces above 120F 49C. Method of Application SCS1000 sealant is easily dispensed directly from cartridges using standard caulking guns or air operated guns. Maximum recommended pressure for air operated guns is 45 psi 0.02 bar. Mixing heating and refrigeration are not required. SCS1000 Contractors silicone sealant Sealant Application Patent Status Begin by installing backup material for joint or joint filler setting blocks spacer shims and tapes as needed. In a continuous operation apply the sealant horizontally in one direction and vertically from the bottom to the top of the joint opening. Apply the sealant with a positive pressure by pushing the bead ahead of the nozzle and making sure that the entire cavity is filled sans air pockets or voids. Tooling should be done neatly forcing the sealant into contact with the sides of the joint or cavity thus helping to eliminate any internal voids and assuring good substrate contact. Sealant should only be applied to surfaces that are clean dry and free of dust. Nothing contained herein shall be construed to imply the non
existence of any relevant patents or to constitute the permission inducement or recommendation to practice any invention covered by any patent without authority from the owner of the patent. Tooling Tool or strike the sealant with a concave tool applying light pressure to spread the material against the back-up material and the joint surfaces to ensure a void-free application. On sill applications tool the sealant to shed water and to eliminate ponding. Tooling agents such as water soap or detergent solutions are not recommended. Cleaning of Excess Sealant For glass metal and plastic surfaces uncured excess material can be removed using a solvent. Use care when using solvents on plastic materials as some solvents can soften some plastics. For glass metal and plastic surfaces cured excess material can be removed using a blade by scraping or cutting. If excess material unintentionally contacts the surfaces of porous materials the sealant is best allowed to progress through the initial cure or set-up and then mechanically removed by abrasion or other suitable means. P. 06 Product Safety Handling and Storage Customers considering the use of this product should review the latest Material Safety Data Sheet and label for product safety information handling instructions personal protective equipment if necessary and any special storage conditions required. Material Safety Data Sheets are available at www.ge.comsilicones or upon request from any MPM representative. Use of other materials in conjunction with GE sealants products for example primers may require additional precautions. Please review and follow the safety information provided by the manufacturer of such other materials. SCS1000 Contractors silicone sealant Emergency Service Momentive Performance Materials maintains an around-the-clock emergency service for its products. Location Emergency Service Provider Emergency Contact Number Mainland U.S. Puerto Rico Alaska Hawaii Canada Europe Israel Middle East Asi
a Pacific except China China Latin America except Brazil Brazil All other locations world wide At sea CHEMTREC CHEMTREC CHEMTREC NCEC NCEC NCEC NCEC NCEC SOS Cotec NCEC Radio U.S. Coast Guard in U.S. waters NCEC in International waters 1-800-424-9300 1-800-424-9300 1-800-424-9300 44 0 1235239670 44 0 1235239671 44 0 1235239670 86-10-5100-3039 44 0 1235239670 08000111767 or 08007071767 44 0 1235239670 44 0 1235239670 For Health related calls contact Momentive Performance Materials at 1-518-233-2500 English only. DO NOT WAIT. Phone if in doubt. You will be referred to a specialist for advice. THE MATERIALS PRODUCTS AND SERVICES OF MOMENTIVE PERFORMANCE MATERIALS INC. MOMENTIVE PERFORMANCE MATERIALS USA INC. MOMENTIVE PERFORMANCE MATERIALS ASIA PACIFIC PTE. LTD. MOMENTIVE PERFORMANCE MATERIALS WORLDWIDE INC. MOMENTIVE PERFORMANCE MATERIALS GmbH THEIR SUBSIDIARIES AND AFFILIATES DOING BUSINESS IN LOCAL JURISDICTIONS collectively SUPPLIERS ARE SOLD BY THE RESPECTIVE LEGAL ENTITY OF THE SUPPLIER SUBJECT TO SUPPLIERS STANDARD CONDITIONS OF SALE WHICH ARE INCLUDED IN THE APPLICABLE DISTRIBUTOR OR OTHER SALES AGREEMENT PRINTED ON THE BACK OF ORDER ACKNOWLEDGMENTS AND INVOICES AND AVAILABLE UPON REQUEST. ALTHOUGH ANY INFORMATION RECOMMENDATIONS OR ADVICE CONTAINED HEREIN IS GIVEN IN GOOD FAITH SUPPLIERS MAKE NO WARRANTY OR GUARANTEE EXPRESS OR IMPLIED i THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE CONDITIONS OR ii AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING SUPPLIERS PRODUCTS MATERIALS SERVICES RECOMMENDATIONS OR ADVICE. AFOREMENTIONED EXCLUSIONS OR LIMITATION OF LIABILITY ARE NOT APPLICABLE TO THE EXTENT THAT THE END-USE CONDITIONS ANDOR INCORPORATION CONDITIONS CORRESPOND TO THE RECOMMENDED CONDITIONS OF USE ANDOR OF INCORPORATION AS DESCRIBED BY SUPPLIER IN ITS PRODUCT DATA SHEET ANDOR PRODUCT SPECIFICATIONS. EXCEPT AS PROVIDED IN SUPPLIERS STANDARD CONDITIONS OF SALE SUPPLIERS AND THEIR REPRESENTATIVES SHALL IN NO EVENT BE RESPONSIBLE
FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS PRODUCTS OR SERVICES DESCRIBED HEREIN. Each user bears full responsibility for making its own determination as to the suitability of Suppliers materials services recommendations or advice for its own particular use. Each user must identify and perform all tests and analyses necessary to assure that its finished parts incorporating Suppliers products materials or services will be safe and suitable for use under end-use conditions. Nothing in this or any other document nor any oral recommendation or advice shall be deemed to alter vary supersede or waive any provision of Suppliers Standard Conditions of Sale or this Disclaimer unless any such modification is specifically agreed to in a writing signed by Suppliers. No statement contained herein concerning a possible or suggested use of any material product service or design is intended or should be construed to grant any license under any patent or other intellectual property right of Suppliers or any of its subsidiaries or affiliates covering such use or design or as a recommendation for the use of such material product service or design in the infringement of any patent or other intellectual property right. GE is a registered trademark of General Electric. Momentive and the Momentive logo are trademarks of Momentive Performance Materials Holdings Inc. Copyright 2007-2013 Momentive Performance Materials Inc. All rights reserved. 161-017-10E-GL CDS DataSCS1000 0113 P. 07
