RB528H www.Mactac.com Version 12 0517 Approved by J. S. Product REBEL RB528H High Tack Product Description RB528P is a 4-mil soft non-top coated opaque matte white polymeric stabilized vinyl coated with an acrylic permanent adhesive. The liner is a 90 SuperFlat C2S polycoated that provides excellent lay flat. This durable flexible vinyl has good outdoor durability. The adhesive has a moderate initial tack and builds to a strong permanent bond with good resistance to creep solvents and heat. Suggested uses include screen-printed labels decals markings point-of-purchase displays and signs for indoor and outdoor use. Physical Properties Property Thickness inches m Face plus adhesive Face adhesive liner Quick Tack lb. in N25mm Stainless Steel Peel Adhesion lb.in. N25 mm Stainless Steel - 30 min. - 24 hrs. - 24 hrs. Heat Aged 158F - 72 hrs. Aluminum - 72 hrs. Powder coated Paint - 72 hrs. Dimensional Stability inches mm 48 hours 158F MD CD Tensile lb. in.N15 mm MD CD Elongation MD CD Typical Values Test Method 0.0055 144 0.0120 305 MACtac CTM-25 3.5 15.3 PSTC-1 4.4 19 6.0 26 7.2 32 7.0 31 8.8 39 4.5 20 0.06 1.5 0.04 1.02 MACtac CTM-21 Method D Bonded to aluminum ASTM D-882 8.0 21 6.0 16 150 80 Temperature Range Application End Use Surface Burning Characteristics Meets ANSI NFPA IFC as class B Flame Spread Smoke Density Opacity 50F min. 10C -40 to 200F -40 to 93C ASTM E84-01 or ANSINFPA 255 or IFC 8-1 75 30 96 - 99 X-Rite Densitometer Color Properties Whiteness and Brightness Brightness ASTM Whiteness CIE Whiteness CIE Tint 88.5 110.24 106.7 2.26 Durability Seven years indoors and up to 5 years outdoors. This use-life estimate is based upon accelerated age studies. Please note that exposure to severe temperatures ultra-violet light and also in tropical sub-tropical or desert regions will cause more rapid deterioration. This also applies to polluted areas high altitude and south facing exposure. Shelf Life This product is good unprinted for two years when stored at 75
F 24C and 50 relative humidity or less. Approved Print Materials Screen Printing UV Cured Solvent WF Digital UV Inkjet Eco-solvent True solvent Latex HP Indigo Off-set UV Off-set Thermal Transfer Flexographic UV Flexographic Narrow Web UV Inkjet Flexographic Printing requires a topcoat. WVG000113 has been approved by ACTEGA Coatings and Sealants ww.altana.com as in-line coat-able ink primers. To achieve the best possible print quality please make sure that the correct ICC profiles or printer settings are used. Profiles can be obtained from our Distributors or can be downloaded from www.mactac.com . Printer and heater settings and ICC profiles can also be downloaded from some O.E.M. or software manufacturers websites. The ICC profiles are provided solely as a customer resource. Print environments the individual nature of printing systems inks and software can significantly affect output. It is the customers responsibility to determine the suitability of any profile for use in their specific print environment. Limitations 1 The user is responsible for determining the products suitability including adhesion and if needed removal characteristics when used in applications other than listed specifically in this Performance Guide. 2 If there are any questions about applications please contact your Mactac sales representative to discuss your requirements for recommendations. 3 If this is a printed Performance Guide it is an uncontrolled document. Please check the Mactac website for the latest most up-to-date version Recommendations Always test your combination of REBEL products inks and laminating films prior to commercial use. 1 Printing Conditions Print in conditioned pressroom at 73F 23C and 50 RH. The maximum allowable ink saturation is 270. 2 Drying Requirements Solvent Eco-solvent and Mild-solvent inkjet prints require 24 - 48 hr. drying time - open to the air. Inks do not dry when printed media is rolled up. The prints must be dry prior to lamination. 3 Laminating
Conditions If the printed graphic is likely to be exposed to corrosive liquids smoke fumes and highly polluted areas or there is a likelihood of scratching it is highly recommended to laminate with Permacolor PermaGard Series High performance or LUV Series intermediate overlaminating films. 4 Transportation Conditions To allow for easy transportation REBEL series can be rolled up with the image out with a minimum diameter of 6 inches 15cm. When the image is not protected by an overlaminate make sure the print is completely dry and protected in a plastic bag. During transportation or storage avoid exposing them to extreme temperature and humidity changes. 5 Applications This film is recommended for use in flat to moderately curved surfaces on a. Vending or dispensing machines and cooler graphics b. Indoor and outdoor graphics and signs c. Small format OEM decorative and identification graphics 6 This film is not recommended for use on a. Corrugated or complex surfaces b. Over rivets c. On flexible substrates banners canvas etc. d. Painted surfaces that are not thoroughly cured or properly bonded to the substrate. Values given are typical for unprocessed product and are not for use as specifications. Processing may change the values. IMPORTANT NOTICE The information given and the recommendations made herein are based on our research and are believed to be accurate but no guarantee of their accuracy or completeness is made. In every case user shall determine before using any product in full scale production or in any way whether such product is suitable for users intended use for their particular purpose under their own operating conditions. User assumes all risk and liability whatsoever in connection with their use of any product. The products discussed herein are sold without any warranty as to merchantability or fitness for a particular purpose or any other warranty express or implied. No representative of ours has any authority to waive or change the foregoing pr
ovisions and no statement or recommendation not contained herein shall have any force of effect unless in an agreement signed by the officers of seller and manufacturer. Nothing contained herein shall be construed to imply the nonexistence of any relevant patents or to constitute a permission inducement or recommendation to practice any invention covered by any patent without authority from the owner of the patent. The following is made in lieu of all warranties express or implied Sellers and manufacturers only obligation shall be to replace or credit such quantity of the product proved to be defective at its discretion. TM Trademark of Morgan Adhesives Company LLC Registered Trademark of Morgan Adhesives Company LLC www.Mactac.com