HYDLAR Z natural - Stock Shapes rods plates tubes Chemical Designation PA 66 Polyamide 66 Main features excellent wear properties excellent strength and stiffness minimizes mating surface abrasion easy to machine high mechanical load capacity Colour yellow-brown Density 1.19 gcm3 Target Industries construction industry conveyor technology gear manufacturing power engineering mechanical engineering Fillers aramide fibres Mechanical properties condition value test method comment Tensile strength 16000 psi ASTM D 638 1 Tensile strength 9500 psi ASTM D 638 2 Modulus of elasticity tensile test 1300000 psi ASTM D 638 3 Modulus of elasticity tensile test 940000 psi ASTM D 638 4 Elongation at break tensile test 4 ASTM D 638 5 Elongation at break tensile test 4.0 ASTM D 638 6 Flexural strength 23000 psi ASTM D 790 7 Flexural strength 16145 psi ASTM D 790 8 Modulus of elasticity flexural test 900000 psi ASTM D 790 9 Modulus of elasticity flexural test 638000 psi ASTM D 790 10 Compression strength 73 F 1 strain 3170 psi ASTM D 695 11 Compression strength 73 F 10 strain 16800 psi ASTM D 695 12 Compression modulus 359000 psi ASTM D 695 13 Impact strength Izod 2.7 ft-lbsin ASTM D 256 14 Impact strength Izod 0.82 ft-lbsin ASTM D 256 15 Rockwell hardness M Scale R Scale 92 116 Wear rate PV2500 psi-fpm 79-128 ASTM D 785 10-10 in3 -minft-lb-hr ASTM D 3702 Thermal properties condition value Deflection temperature 264 psi 470 F ASTM D 648 1 Service temperature Intermittent 300 F - 2 Service temperature Long Term 200 F - 3 1.610 -5 ininF ASTM D 696 4 Thermal expansion CLTE test method Other properties condition value Moisture absorption 24 hrs 73 F 0.37 ASTM D 570 Moisture absorption saturation 73 F 6.3 ASTM D 570 1 Injection molded samples 2 Extruded - property values dependent upon shape and cross sectional area 3 Injection molded samples 4 Extruded - property values dependent upon shape and cross sectional area 5 Injection molded samples 6 Extruded - property values dependent
upon shape and cross sectional area 7 Injection molded samples 8 Extruded - property values dependent upon shape and cross sectional area 9 Injection molded samples 10 Extruded - property values dependent upon shape and cross sectional area 11 Extruded - property values dependent upon shape and cross sectional area 12 Extruded - property values dependent upon shape and cross sectional area 13 Extruded - property values dependent upon shape and cross sectional area 14 Injection molded samples 15 Extruded - property values dependent upon shape and cross sectional area comment test method 1 Data obtained from public source 2 Data obtained from public source 3 Data obtained from public source 4 Data obtained from public source comment 1 1 Data obtained from public source Resin specification ASTM D6779-11 PA0100 Shapes specification ASTM D 5989 S-PA0101R2052154000 This information reflects the current state of our knowledge and is intended only to assist and advise. It is given without obligation or liability. It does not assure or guarantee chemical resistance quality of products or their suitability in any legally binding way. Values are not minimum or maximum values but guidelines that can be used for comparative purposes in material selection. They are within the normal range of product properties and do not represent guaranteed property values. Testing under individual application circumstances is always recommended. Data is obtained from extruded shapes material unless otherwise noted. References to FDA compliance refer to the resins from which the products were made unless otherwise noted. All trade and patent rights should be observed. All rights reserved. Data sheet values are subject to periodic review the most recent update can be found at www.ensingerplastics.com. Ensinger Inc. Headquarters 365 Meadowlands Boulevard Washington PA 15301 USA Phone 800-243-3221 Sales Phone 800-869-4029 Technical Fax 724-746-9209 salesensingerusa.com Date 20180606 Version A1