Product Name Performance Translucent White Product Reference TWPAG30C Page Revision Date Replaces Authors 12 2 CVNA 01 February 2019 D RAS Description Performance TWPAG30C is a Translucent White perforated self-adhesive vinyl with 30 transparency and a removable pressure-sensitive adhesive featuring a Universal Liner with Grayliner technology. This film is used to create backlit see-through graphics. This allows an image to be seen on the outside of a window during the day while allowing viewing through from the inside and during the hours of darkness allows the image to be backlit so that it can still be seen on the outside. A ghost reverse image of the print can be seen from the inside although the mind will concentrate on the outside view and not the ghost image. This promotional film features a part-perforated paper liner and is intended for UV-cure solvent eco-solvent and latex inkjet printing and screenprinting. PROPERTY Face film Film thickness Hole pattern Adhesive Liner Liner weight Application temperature Peel adhesion 24 hours Peel adhesion 1 month Removability Durability Typical Properties VALUE Translucent White polymeric calendered pvc 55-60 opacity 40-45 transmission when unperforated. 7.1 mil 0.4 mil 180m 10 m 30 transparency 0.06 1.50mm diameter holes Transparent solvent polyacrylate 1.23 ozyard2 0.09 ozyard2 35gm2 3gm2 Part-perforated Universal Liner. Perforated silicone coated paper laminated with grey-printed paper backprinted with Contra Vision Performance branding. 5.75 ozyard2 0.18 ozyard2 163gm2 5gm2 after perforating Minimum 39F 4C air and substrate 14.4 ozIn4N25mm Printed film on glass typical value 18 ozin 5N25mm. Printed film on glass typical value Minimum 12 months clean removability without adhesive residue at 73F to 77F 23C to 25Cand RH of 50-60 3 years Durability stated is for unprinted and untreated material correctly applied to an inert vertical substrate subject to MidEuropean weathering conditions. Some printing inks and drying
or curing regimes may reduce the expected lifetime of the printed graphic. Please consult your ink manufacturer for guidance. Incorrect application methods inadequate window cleaning and preparation and incompatible window treatments may reduce the expected lifetime of the applied material whether printed or unprinted overlaminated or unlaminated. Mechanically sustained damage chemical damage and UVdegradation to printed unprinted laminated or unlaminated material may also reduce expected durability. Typical application life is eighteen months. All perforated window films are especially vulnerable to damage along the edges and corners which may lead to premature failure. Shrinkage Service temp Shelf life x direction 0.6 y direction 0.6 FTM14 -13F to 149F -25C to 65C 2 years Under ordinary condition at temperature of 72F 22 and relative humidity of 50-55 Other info Copyright Contra Vision North America Inc. 2019 www.contravision.com Product Name Performance Translucent White Product Reference TWPAG30C Page Revision Date Replaces Authors 22 2 CVNA 01 February 2019 D RAS Regulations Some countries and regions have laws or regulations requiring minimum light passage that may limit or preclude the use of this product on vehicle windows. The user is responsible for determining and complying with all applicable standards. Substrate Recommendations This product is not recommended for use on glass with coatings such as anti-reflective self-cleaning and scratch-resistance which may be damaged during film removal. Application Recommendations Apply the film using a dry application method. Surfaces to which the material will be applied must be thoroughly cleaned from dust grease or any contamination. Final clean with soap and water. Rinse and dry glass after cleaning. Not to be applied to fresh paint or ink polycarbonate rubber plastic moldings and certain PVCs. In case of doubt please test prior to final application. This product is not recommended for use around a sharp angl
e where there is a limited area either side of the angle. The film must not touch the rubber window molding. If two graphic panels meet side by side on a window carefully trim the film so that the panels meet and form a butt seam. Do not overlap the panels. Observe the minimum application temperature and the graphics should not be washed within 24 hours of application. Printing Recommendations Universal Liner construction correctly printed eliminates the bridging over the perforated holes that can occur with UV curing inkjet printers and Replacement Liner construction. After printing the ink must be thoroughly dry including in the perforated holes to avoid any contamination particularly during lamination. Contact Information Contra Vision North America Inc. Supplier 3330 Cumberland Blvd Suite 500 Atlant a USA Tel. 1 770 993 6262 Email usasalescontravision.com Web www.contravision.com This document is intended as a source of information is given without guarantee and does not constitute a warranty. Purchasers should independently determine prior to use the suitability of the product for their specific intended purpose. All trademarks in this datasheet are Contra Vision Ltd Copyright Contra Vision North America Inc. 2019 www.contravision.com
